Dicodes Chipsets - V3 / BF60 / FL80

Dicodes electronics are the most advanced electronics available on the market in temperature-controlled mods.

Made in Germany

*** IN-STOCK FOR IMMEDIATE PROCESSING ***

$125.00
Availability: In stock
SKU
DCM000024
 
Dicodes BF60  Chipset  
 
Small form factor PCB for use of single 18650 or 26650 cells. The board has a max of 60W power output including 5 modes of operation, Power(W), Temp-control, Heater-Protection, Boost, and Bypass. Please contact us for more detailed specifications.

Features:

  • Output power 5 - 60W
  • Stable and reliable temperature control
  • Resistance range 0.05Ω - 5Ω

 

Contents:

  • Dicodes BF60 Chipset & LCD Display

 

Data Sheet / Installation Manual:

 

*Warranty Terms

All Dicodes chipsets are thoroughly tested during production to make sure they are not faulty.  Due to the user intervention that is required to install the board ie., misuse or mistreatment, including improper installation or testing which may cause damage to the circuitry, there is no warranty supplied.

All boards are tested to meet USA and EU consumer safety, health and environmental requirements.

Please Note: 

In order for the temperature control settings to function, a coil made from NiFe30, Titanium, Ni200, Tungsten, adjustable („other“) wire must be used, no exceptions. Coils made with Standard Nichrome or Kanthal A1 wire will only support wattage mode, so the temperature control feature cannot be utilized.

  

Dicodes FL80  Chipset   

Power regulation electronic board for use of either single cell 18650 or dual cell applications (max power when using dual cells is 80W.)  Also compatible with single cell 20700 or 21700 as the chemistry is the same as with standard 18650 batteries.  Please note: (You cannot charge LiFePo batteries with the FL80 onboard charger circuit, because these batteries have a charge end voltage of type. 3.7V instead of 4.2V on standard 18650/21700 batteries.  ** For additional information, please see the detailed specifications and wiring documentation below on this very advanced PCB.

Features:

  • Max 80W output (60W for single cell configurations), or 20700 / 21700 (60W for single cell configurations)
  • Full-featured Dicodes user interface

 

Contents:

  • Dicodes FL80 Chipset & LCD Display

Data Sheet / Installation Manual:

 

*Warranty Terms

All Dicodes boards are thoroughly tested during production to make sure they are not faulty.  Due to the user intervention that is required to install the board ie., misuse or mistreatment, including improper installation or testing which may cause damage to the circuitry, there is no warranty supplied.

All boards are tested to meet USA and EU consumer safety, health and environmental requirements.

Please Note: 

In order for the temperature control settings to function, a coil made from NiFe30, Titanium, Ni200, Tungsten, adjustable („other“) wire must be used, no exceptions. Coils made with Standard Nichrome or Kanthal A1 wire will only support wattage mode, so the temperature control feature cannot be utilized.

 

Dicodes V3 Chipset   

Power regulation electronic board for use with a single cell 18650 cell applications (max power when using dual cells is 80W.)  Please note: (You cannot charge LiFePo batteries with the V3 onboard charger circuit, because these batteries have a charge end voltage of type. 3.7V instead of 4.2V on standard 18650/21700 batteries.  ** For additional information, please see the detailed specifications and wiring documentation below on this very advanced PCB.

Features:

  • Max 80W output (60W for single-cell configurations)
  • Full-featured Dicodes user interface

 

Contents:

  • Dicodes V3 Chipset & LCD Display

Data Sheet / Installation Manual:

 

*Warranty Terms

All Dicodes boards are thoroughly tested during production to make sure they are not faulty.  Due to the user intervention that is required to install the board ie., misuse or mistreatment, including improper installation or testing which may cause damage to the circuitry, there is no warranty supplied.

All boards are tested to meet USA and EU consumer safety, health, and environmental requirements.

Please Note: 

In order for the temperature control settings to function, a coil made from NiFe30, Titanium, Ni200, Tungsten, adjustable („other“) wire must be used, no exceptions. Coils made with Standard Nichrome or Kanthal A1 wire will only support wattage mode, so the temperature control feature cannot be utilized.

Write Your Own Review
Only registered users can write reviews. Please Sign in or create an account
We found other products you might like!